Wright Serial 54956 and higher User Manual

1 Instruction Manual Wright Manufacturing 4600X Wedgewood Blvd Frederick, Md 21703 Small Frame Standers serial # 54956 and higher WARNI

10 WARNING WARNING WARNING • When transporting, driving onto transport vehicles, into buildings, across parking lots or otherwise

11 WARNING WARNING 1.15 Zero-Radius Turn Operation During zero-radius turns (when one mower wheel rotates backwards while the other rotat

12 WARNING WARNING 1.17 Fuel Safety Handle gasoline with care – it is highly flammable. Do not smoke while handling gasoline. Use an ap

13 76490013, DECAL, MAIN INST. PANEL 2 Warning, Safety and Instructional Decals • Specific safety warning decals are located on the equipment near im

14 Critical Application ModelsThread LockerTorque Range (ft-lbs)Wheel motor bolts (Securing motor to support)Small Stander Loctite 2760 40-50Clutch t

15 1 2 3 4 5 7 6 8 9 11 10 12 4 Machine Description & Overview The Wright Stander is meant to solely cut, bag or mulch grass. The use for any ot

16 1 3 2 5 4 4.1 Operator’s Area 1. Anti-Tip Wheels 2. Brake Handle 3. Dash Panel 4. Thigh Cushion 5. Foot Platform 4.2 Model & S

17 4.3 Control Panel & Steering Control Levers The Stander speed and direction are controlled by using the control handles. Moving the control h

18 4.6 Brake Interlock System The Wright Stander is equipped with a brake interlock. When the parking brake is applied, the control handles are lock

19 Brake Off Brake ON WARNING WARNING • Check to see if the equipment has a separate choke knob or whether it is incorporated into the

2 Foreword Welcome to the progressive group of mowing professionals who use Wright mowers. We are focused on giving you advanced engineering and qua

20 WARNING WARNING A 5.5 Driving the Mower Over a Curb To climb a curb, first see the Safety Instructions section of this manual, especiall

21 Slow Hole Fast Hole 5.8 Changing the Speed/Sensitivity Adjustment The controls are initially set with the Speed/Sensitivity Adjustment in the fast

22 WARNING 5.10 How to Test/Use the Blade Clutch/Brake Switch Before testing the blade clutch/brake operation, make sure the area is clear and th

23 b. The front-to-rear leveling of the blades should be between level (preferred) to .25" lower at the front of the blades but never higher at

24 6.3.2 Replacing the Drive Belt • Stop the engine, remove the key and wait for all moving parts to stop. • Remove the deck cover and remove the b

25 6.6 Bleeding Air from the Hydraulic System First, make sure the oil level in the reservoir is correct. The oil should be level with the bottom th

26 6.10 Fuel Evaporation System All Wright Standers need to have this mandatory feature. • Do Not alter or remove. • Do Not fill past the “Max Fi

27 WARNING WARNING 6.12 Cutting Blades In order to maintain the best cut, it is important that the blades are well sharpened and not damaged.

28 6.16 Kawasaki Engine Manual / Maintenance It is very important that all users of this unit read and understand the Kawasaki Engine Owner’s Manual.

29 7 Electrical Schematic (Recoil / Electric Start)

3 Table of Contents PRE DELIVERY SERVICE BY DEALER ...

30 7.1 Electrical Schematic (Recoil)

31 8 Decals 1 76490004 Decal, Stander 2 76490013 Decal, Main Inst. Panel, Dash 3 76490005 Decal, Throttle / Instructions

32 MAINTENANCE ITEMENGINE ITEMSSEE NOTE BELOWFIRST 8 HOURSDAILYEVERY 25 HOURSEVERY 100 HOURSEVERY 200 HOURSEVERY 300 HOURSANNUALLYInspect for cracks

33 Date Maintenance/Service PerformedUnit HoursShop/TechnicianMaintenance Record

34 Wright Manufacturing, Inc. (hereinafter: WMI) warrants to the original owner that the new WMI mower accompanying this document will be

35 FEDERAL AND CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The United States Environmental Protection Agenc

36 (3) Any warranted part that is scheduled for replacement as required maintenance in the written instructions supplied is warranted for the period

37 Problem Description Possible Cause SolutionStreaking is when strips of uncut grass are left behind. Blades are not sharp Sharpen bladesBlades ar

38 NOTES:

39 NOTES:

4 PRE-DELIVERY SERVICE OF MOWER BY DEALER Before proceeding with the Pre-Delivery Service of your mower, please read the safety instructions manual i

40 4600X Wedgewood Blvd Frederick, MD 21703 www.wrightmfg.com

5  With the blades on, disengage the OPC switch to test the Operator Presence Control switch (OPC). A time delay has been added to the OPC system

6 1. Introduction This mower is built to the highest standards in the industry. However, carelessness or operator error may result in serious bodily

7 Do's Don'tsRead the operators manual before attempting to operate this machine Don't disable safety switchesUse all PPE's, eye

8 WARNING WARNING WARNING WARNING WARNING 1.3 Important Information It is vital that these instructions are available t

9 WARNING WARNING WARNING operator safety. Ensure deck pitch is between 1/4 - 3/8”. (Refer to the maintenance interval chart at t